|
Hopefully, this page is exactly what you are looking for, but if not, you can always find further assistance on Unix/Linux Forum!
WRITE(2) Linux Programmer's Manual WRITE(2)
NAME
write - write to a file descriptor
SYNOPSIS
#include <unistd.h>
ssize_t write(int fd, const void *buf, size_t count);
DESCRIPTION
write() writes up to count bytes to the file referenced by the file
descriptor fd from the buffer starting at buf. POSIX requires that a
read() which can be proved to occur after a write() has returned
returns the new data. Note that not all file systems are POSIX con-
forming.
RETURN VALUE
On success, the number of bytes written are returned (zero indicates
nothing was written). On error, -1 is returned, and errno is set
appropriately. If count is zero and the file descriptor refers to a
regular file, 0 will be returned without causing any other effect. For
a special file, the results are not portable.
ERRORS
EAGAIN Non-blocking I/O has been selected using O_NONBLOCK and the
write would block.
EBADF fd is not a valid file descriptor or is not open for writing.
EFAULT buf is outside your accessible address space.
EFBIG An attempt was made to write a file that exceeds the implementa-
tion-defined maximum file size or the process' file size limit,
or to write at a position past the maximum allowed offset.
EINTR The call was interrupted by a signal before any data was writ-
ten.
EINVAL fd is attached to an object which is unsuitable for writing; or
the file was opened with the O_DIRECT flag, and either the
address specified in buf, the value specified in count, or the
current file offset is not suitably aligned.
EIO A low-level I/O error occurred while modifying the inode.
ENOSPC The device containing the file referred to by fd has no room for
the data.
EPIPE fd is connected to a pipe or socket whose reading end is closed.
When this happens the writing process will also receive a SIG-
PIPE signal. (Thus, the write return value is seen only if the
program catches, blocks or ignores this signal.)
Other errors may occur, depending on the object connected to fd.
CONFORMING TO
SVr4, 4.3BSD, POSIX.1-2001.
Under SVr4 a write may be interrupted and return EINTR at any point,
not just before any data is written.
NOTES
A successful return from write() does not make any guarantee that data
has been committed to disk. In fact, on some buggy implementations, it
does not even guarantee that space has successfully been reserved for
the data. The only way to be sure is to call fsync(2) after you are
done writing all your data.
SEE ALSO
close(2), fcntl(2), fsync(2), ioctl(2), lseek(2), open(2), pwrite(2),
read(2), select(2), writev(2), fwrite(3)
Linux 2.0.32 2001-12-13 WRITE(2)
Man(1) output converted with
man2html and wrapped by fishsponge
This page was generated on Sat Sep 8 16:35:43 GMT 2007
|
Your favourite pages:
No pages logged yet.
Trying to save cookie... Top 10 most popular pages:
svn man page (6161 hits)
(FreeBSD 6.2)
sqlite3 man page (5598 hits)
(openSUSE 10.2)
adv_cap_autoneg man page (5045 hits)
(Solaris 10 11_06)
CPAN man page (4791 hits)
(Suse Linux 10.1)
ssh man page (4439 hits)
(Suse Linux 10.1)
ssh-socks5-proxy-connect man page (3525 hits)
(Solaris 10 11_06)
signal man page (3395 hits)
(Suse Linux 10.1)
netcat man page (3373 hits)
(Suse Linux 10.1)
pprosetup man page (2886 hits)
(Solaris 10 11_06)
startproc man page (2738 hits)
(Suse Linux 10.1)
|
Man Pages 
